Type code | CMMT-AS |
---|---|
Fieldbus interface, function | Bus connection, incoming/forwarding EtherNet/IP slave |
KC characters | KC EMC |
Fieldbus interface, transmission rate | 100 Mbit/s |
Mounting position | Free convection Vertical |
Information on max. installation height | 1% power reduction/100 m above 1000 m. |
Ethernet interface, protocol | TCP/IP |
Ethernet interface, function | Parameterization and commissioning |
Encoder interface, function | EnDat® 2.1 encoder EnDat® 2.2 encoder Hiperface encoder Incremental encoder Nikon SIN/COS encoder |
Fieldbus interface, connection technology | RJ45 |
Mains types | TN IT |
Protection class | I |
Encoder interface 2, function | Incremental encoder SIN/COS encoder |
Fieldbus interface, protocol | EtherNet/IP |
Overvoltage category | III |
Synchronization interface, function | Encoder emulation A/B/Z Encoder input A/B/Z Pulse/direction signals CLK/DIR CW/CCW counting signals |
Fieldbus interface, connection type | 2x socket |
Number of high-speed switching outputs | 2 |
Number of floating switching outputs | 1 |
Number of inputs for motor temperature sensor | 1 |
Number of diagnostic outputs | 2 |
Max. current of the floating switching outputs | 50 mA |
Max. continuous output of the external braking resistor (IEC) | 1500 W |
Pulse energy for braking resistor | 1200 Ws |
Max. output current of holding brake | 1.5 A |
Number of high-speed logic inputs | 2 |
System voltage to EN 61800-5-1 | 300 V |
Max. short circuit protection of mains | 10 kA |
Braking resistor nominal power (IEC) | 100 W |
Max. voltage drop from logic supply to brake output | 1 V |
Number of safe 2-pin inputs | 2 |
Time resolution of high-speed logic inputs | 1 µs |
Max. current consumption for logic supply with parking brake | 2 A |
Max. installation height | 2000 m |
Time resolution of high-speed switching outputs | 1 µs |
Based on norm | EN 50581 EN 60204-1 EN 61508-1 EN 61508-2 EN 61508-3 EN 61508-4 EN 61508-5 EN 61508-6 EN 61508-7 EN 61800-2 EN 62061 |
Conforms to standard | EN 61800-3 EN 61800-5-1 EN 61800-5-2 EN ISO 13849-1 |
Active PFC | no |
Controller operating mode | Cascade control P position controller PI speed controller PI current regulator for F or M Profile operation with block mode and direct mode Interpolating mode via fieldbus Synchronous operating modes Reference travel Setup mode Autotuning |
Mode of operation | Field-oriented regulation Position resolution 24 bit/rev. Sampling rate 16 kHz PWM with 8 or 16 KHz Vector modulation with 3rd harmonic Real-time data acquisition 2x input capture (x, v, F) 2x output trigger (x, v, F) 2x position sensor input 1x SYNC interface for encoder emulation or encoder input |
Line filter | Integrated |
Safety function | Safe brake control (SBC) Safe torque off (STO) Safe stop 1 (SS1) |
Safety integrity level (SIL) | Safe brake control (SBC)/SIL 3/SILCL 3 Safe torque off (STO)/SIL 3/SILCL 3 |
Performance Level (PL) | Safe brake control (SBC)/category 3, performance level e Safe torque off (STO)/category 4, performance level e |
Display | LED green/yellow/red |
Control elements | Optional: CDSB operating unit |
Output frequency | 0 Hz … 599 Hz |
Output voltage range AC | 3x (0 – input) V |
Braking resistor, external | 60 Ohm … 85 Ohm |
Braking resistor, integrated | 47 Ohm |
Diagnostic coverage | 97 % |
Characteristics of digital logic outputs | Freely configurable in some cases Not galvanically isolated Diagnostic outputs in some cases |
Hardware fault tolerance | 1 |
Impedance of setpoint input | 70 kOhm |
Pulse power of braking resistor | 13.6 kVA |
Max. current of digital logic outputs | 20 mA |
Max. length of motor cable without ext. mains filter | 25 m |
Max. peak current duration | 2 s |
Max. DC link voltage | 800 V |
Nominal operating voltage AC | 400 V |
Input voltage range AC | 200 V … 480 V |
Controller nominal power | 4000 VA |
Nominal voltage, logic supply DC | 24 V |
Nominal voltage, load supply DC | 560 V |
Nominal current load supply | 9 A |
Nominal current per phase, effective | 7 A |
Mains frequency | 48 Hz … 62 Hz |
Nominal operating voltage phases | 3-phase |
SFF safe failure fraction | 99 % |
Peak power | 12000 VA |
Peak current, load supply | 27 A |
Peak current per phase, effective | 21 A |
Surge resistance | 6 kV |
Max. current consumption for logic supply without clamping brake | 0.5 A |
Max. current consumption for logic supply with clamping brake and I/O | 2.5 A |
Contamination level | 2 |
Load supply permissible range | ± 10 % |
Permissible range of logic voltage | ± 20 % |
Permissible voltage fluctuations | +/- 10 % |
Certificate issuing authority | German Technical Control Board (TÃœV) Rheinland 01/205/5640.00/18 UL E331130 |
CE marking (see declaration of conformity) | As per EU EMC directive as per EU machinery directive As per EU low voltage directive As per EU RoHS directive |
Storage temperature | -25 °C … 55 °C |
Relative air humidity | 5 – 90 % Non-condensing |
Degree of protection | IP20 |
Ambient temperature | 0 °C … 50 °C |
Note on ambient temperature | Above an ambient temperature of 40 °C, the power must be reduced by 3%/°C. |
UL-ambient temperature | 0 °C … 40 °C |
Certification | RCM compliance mark German Technical Control Board (TÃœV) c UL us – Listed (OL) |
Product weight | 4100 g |
Number of analog setpoint inputs | 1 |
Number of digital logic outputs 24 V DC | 6 |
Number of digital logic inputs | 12 |
Communication profile | DriveProfile |
Process interfacing | Adjustable-Speed Drives Drives with positioning function |
Logic input specification | Based on IEC 61131-2, type 3 |
Work range of logic input | -3 V … 30 V |
Work range of setpoint input | ± 10 V |
Operating range of analog inputs | ± 10 V |
Encoder interface output, characteristics | 1 MHz maximum output frequency max. 16384 ppr |
Encoder interface input, characteristics | 1 MHz maximum output frequency max. 16384 ppr |
Characteristics of setpoint inputs | Differential inputs Configurable for rotational speed Configurable for current/force |
Characteristics of logic input | Freely configurable in some cases Safety inputs in some cases Not galvanically isolated |
Input switching logic | PNP (positive switching) |
Switching logic at outputs | PNP (positive switching) |
Fieldbus coupling | EtherNet/IP |
Type of mounting | Mounting plate, screwed on |
Note on materials | Contains paint-wetting impairment substances RoHS-compliant |
CMMT-AS-C7-11A-P3-EP-S1
$2,758.72
GTIN: 4052568555856
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet.