| Type code | CMMT-ST |
|---|---|
| Fieldbus interface, function | Bus connection, incoming/forwardingEtherNet/IP slave |
| KC characters | KC EMC |
| Fieldbus interface, transmission rate | 100 Mbit/s |
| Mounting position | Free convectionVertical |
| Ethernet interface, protocol | TCP/IP |
| Ethernet interface, function | Parameterization and commissioning |
| Encoder interface, function | BiSS-CIncremental encoder |
| Fieldbus interface, connection technology | RJ45 |
| Protection class | III |
| Proof test interval | STO / 20 a (stepper motor/EC-motor without diagnostics) |
| Fieldbus interface, protocol | EtherNet/IP |
| Overvoltage category | I |
| Fieldbus interface, connection type | 2x socket |
| Number of high-speed switching outputs | 2 |
| Number of floating switching outputs | 1 |
| Number of diagnostic outputs | 1 |
| Max. current of the floating switching outputs | 100 mA |
| Max. output current of holding brake | 1 A |
| Number of high-speed logic inputs | 2 |
| Max. voltage drop from logic supply to brake output | 1 V |
| Number of safe 2-pin inputs | 1 |
| Time resolution of high-speed logic inputs | 1 µs |
| Max. current consumption for logic supply with parking brake | 2 A |
| Max. installation height | 2000 m |
| Time resolution of high-speed switching outputs | 1 µs |
| Diagnostic coverage | STO: 87% (EC motor without diagnostics)STO / 90% (stepper motor)STO: 92% (EC motor with diagnostics) |
| Controller operating mode | Cascade controlP position controllerPI speed controllerPI current regulator for F or MProfile operation with block mode and direct modeInterpolating mode via fieldbusSynchronous operating modesReference travelSetup modeAutotuningOpen-loop operation |
| Mode of operation | Field-oriented regulationPosition resolution 24 bit/rev.Sampling rate 20 kHzPulse-width modulation with 20 kHzReal-time data acquisition2x input capture (x, v, F)2x output trigger (x, v, F)1x position sensor input |
| Adjustable current reduction | Via software |
| Protective function | I²t monitoringTemperature monitoringCurrent monitoringVoltage failure detectionContouring error monitoringSoftware end position detection |
| Safety function | Safe torque off (STO)Safe stop 1 with time control (SS1-t) |
| Safety integrity level (SIL) | STO / SIL 2 / SILCL 2 (EC motor without diagnostics)STO / SIL 3 / SILCL 3 (stepper motor/EC motor with diagnostics) |
| Performance Level (PL) | STO: cat. 3 PLd (EC motor without diagnostics)STO/cat. 3, PLe (stepper motor/EC motor with diagnostics) |
| Display | LED green/yellow/red |
| Nominal current setting | Via software |
| Output frequency | 0 Hz … 20000 Hz |
| Output voltage range AC | 0 V up to input voltage |
| Characteristics of digital logic outputs | ConfigurableNot galvanically isolated |
| Hardware fault tolerance | 1 |
| Max. current of digital logic outputs | 100 mA |
| Max. length of motor cable without ext. mains filter | 25 m |
| Max. peak current duration | 3 s |
| Max. DC link voltage | 60 V |
| Nominal output current | 8 A |
| Controller nominal power | 300 VA |
| Nominal voltage, logic supply DC | 24 V |
| Nominal voltage, load supply DC | 24 V … 48 V |
| Nominal current per phase, effective | 8 A |
| Peak power | 400 VA |
| Peak current per phase, effective | 10 A |
| Max. current consumption for logic supply without clamping brake | 1 A |
| Contamination level | 2 |
| Load supply permissible range | -15% / +15% |
| Permissible range of logic voltage | ± 15 % |
| Certificate issuing authority | German Technical Control Board (TÃœV) Rheinland 01/205/5696.00/19UL E331130 |
| CE marking (see declaration of conformity) | As per EU EMC directiveas per EU machinery directiveAs per EU RoHS directive |
| Storage temperature | -25 °C … 55 °C |
| Relative air humidity | 5 – 90 %Non-condensing |
| Degree of protection | IP20 |
| Ambient temperature | 0 °C … 50 °C |
| Note on ambient temperature | Observe derating with regard to assembly distance and output current. |
| Certification | RCM compliance markc UL us – Listed (OL) |
| Product weight | 350 g |
| Number of digital logic outputs 24 V DC | 2 |
| Number of digital logic inputs | 6 |
| Communication profile | DriveProfile |
| Process interfacing | Adjustable-Speed DrivesDrives with positioning function |
| Logic input specification | Based on IEC 61131-2, type 3 |
| Work range of logic input | -3 V … 30 V |
| Characteristics of logic input | Freely configurable in some casesSafety inputs in some casesNot galvanically isolated |
| Input switching logic | NPN (negative switching)PNP (positive switching) |
| Switching logic at outputs | NPN (negative switching)PNP (positive switching) |
| Type of mounting | Mounting plate, screwed onWith H-rail |
| Note on materials | Contains paint-wetting impairment substancesRoHS-compliant |
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet